六角護坡模具生產過程中以聚丙烯為主要原料。這種材料的優點是它具有很強的韌性和防墜落性能。澆筑混凝土時，護坡用六角磚模具能承受其壓力，且仍保持模具不變。其應用場所主要是高鐵工程、高速工程、水利工程、市政工程。 Hexagon revetment mold production process of polypropylene as the main raw material. The advantages of this kind of material is that it has a strong toughness and fall prevention performance. Pouring concrete, the slope protection with hexagon brick mold can withstand the pressure, and still keep the mould remains the same. Its main application place is high-speed railway engineering, highway engineering, municipal engineering, water conservancy project.
六邊形護坡功能較高，但在應用過程中如果達不到存放要求，更容易出現六邊形護坡模具變形，影響模具的生產和應用。因此，正確應用六角磚護坡模具可以延長模具的使用壽命。 Hexagon revetment function is higher, but if not stored in the process of application requirements, more prone to hexagon revetment mold deformation, influence the mold production and application. Therefore, the correct application of hexagonal brick mold can prolong the service life of mould.
六角護坡模具應用中的注意事項：
Hexagon revetment mould matters needing attention in the application:
1. The correct use of hexagon revetment mould can extend the life of the mold.
2.禁止露天存放在陽光直射的地方。
2. The ban open-air stored in direct sunlight.
3.禁止使用未經測試的脫模劑、廢機油、蠟等。涂抹在塑料模具上，會嚴重破壞護坡六角磚模具的韌性和強度，導致開裂和風化。
3. To ban the use of untested tuomoji, waste oil, wax, etc. Daub is on plastic mould, can play havoc with slope protection hexagon brick mould toughness and strength, leading to cracking and weathering.
4.禁止在超過40度的溫度下蒸模。
4. The ban on more than 40 degrees under the temperature of the steam.
5.經過反復加熱和冷卻后，六角護坡模具的尺寸會減小，平整度會發生變化。如果達不到應用標準，建議更換。
5. After repeated heating and cooling, hexagon revetment tends to decrease the size of the mould, flatness change. If can not meet the application standard, it is suggested that replacement.
6.建議混凝土在使用過程中加入三聚氰胺樹脂減水劑，可減少粘模和延模壽命。
6. Recommend concrete adding melamine resin in the process of using water reducing agent, can reduce viscosity mold and die life.
7.維護時確�，F場的平整度和邊緣對齊，以保證產品質量。
7. When maintenance to ensure that the scene of flatness and edge alignment, to ensure product quality.
8.使用振蕩頻率匹配的振動臺，應減少深腔產品的振蕩時間。過大的振動力和長時間的振動會對塑料模具造成損壞。
8. The use of vibration table, oscillation frequency matching should be less deep cavity oscillation time of the products. Excessive vibration and the vibration of the long time can cause damage to plastic mold.
9.脫模時嚴禁用硬工具敲打護坡六角磚模具，盡量用橡膠錘輕敲。
9. Parting when tapping revetment hexagon brick mold, it is forbidden to use the hard tool as far as possible with a rubber hammer tapping.
10.脫模后，需要將護坡六角磚模具堆放在室內，防止變形。
10. After demoulding, hexagon brick mold need to revetment pile up indoors, to prevent deformation.
經過以上應用方式，無論模具是用PP丙綸塑料還是ABS塑料注塑成型，六角護坡模具在后期二次和多次澆注過程中，都不容易變形損壞，產品的使用壽命可以大大延長。
After the above application way, regardless of the mold is made of PP polypropylene plastic and ABS plastic injection molding, hexagon revetment mold in the late second and pouring process for many times, is not easy deformation and damage, the service life of the product can be greatly extended.
